This section contains information about what hardware you need to get started with Debian. You will also find links to further information about hardware supported by GNU and Linux.
Debian does not impose hardware requirements beyond the requirements of the
Linux kernel and the GNU tool-sets. Therefore, any architecture or platform to
which the Linux kernel, libc, gcc, etc. have been ported, and for
which a Debian port exists, can run Debian. Please refer to the Ports pages at
http://www.debian.org/ports/arm/
for more details on arm architecture systems which have been tested with
Debian.
Rather than attempting to describe all the different hardware configurations which are supported for ARM, this section contains general information and pointers to where additional information can be found.
Debian 3.0 supports eleven major architectures and several variations of each architecture known as 'flavors'.
Architecture | Debian Designation / Flavor
---------------------+----------------------------
Intel x86-based | i386
| - vanilla
| - idepci
| - compact
| - bf2.4 (experimental)
|
Motorola 680x0: | m68k
- Atari | - atari
- Amiga | - amiga
- 68k Macintosh | - mac
- VME | - bvme6000
| - mvme147
| - mvme16x
|
DEC Alpha | alpha
| - generic
| - jensen
| - nautilus
|
Sun SPARC | sparc
| - sun4cdm
| - sun4u
|
ARM and StrongARM | arm
| - netwinder
| - riscpc
| - shark
| - lart
|
IBM/Motorola PowerPC | powerpc
- CHRP | - chrp
- PowerMac | - powermac, new-powermac
- PReP | - prep
- APUS | - apus
|
HP PA-RISC | hppa
- PA-RISC 1.1 | - 32
- PA-RISC 2.0 | - 64
|
Intel ia64-based | ia64
|
MIPS (big endian) | mips
- SGI Indy/I2 | - r4k-ip22
|
MIPS (little endian) | mipsel
- DEC Decstation | - r4k-kn04
| - r3k-kn02
|
IBM S/390 | s390
| - tape
| - vmrdr
|
---------------------+----------------------------
This document covers installation for the arm architecture. If you
are looking for information on any of the other Debian-supported architectures
take a look at the Debian-Ports pages.
Debian only runs on little-endian ARM processors. Supported machines include NetWinder, CATS, RiscPC, Shark and LART.
Debian's support for graphical interfaces is determined by the underlying
support found in XFree86's X11 system. The newer AGP video slots are actually
a modification on the PCI specification, and most AGP video cards work under
XFree86. Details on supported graphics buses, cards, monitors, and pointing
devices can be found at http://www.xfree86.org/. Debian 3.0
ships with X11 revision 4.1.0.
CD-ROM based installation is supported for some architectures. On machines which support bootable CD-ROMs, you should be able to do a completely floppy-less installation. Even if your system doesn't support booting from a CD-ROM, you can use the CD-ROM in conjunction with the other techniques to install your system, once you've booted up by other means; see Booting from a CD-ROM, Section 5.2.
IDE/ATAPI CD-ROMs are supported on all ARM machines. On RiscPCs, SCSI CD-ROMs are also supported.
Installation system booting from a hard disk is another option for many architectures.
You can also boot your system over the network. Diskless installation, using network booting from a local area network and NFS-mounting of all local filesystems, is another option — you'll probably need at least 16MB of RAM for a diskless installation. After the operating system kernel is installed, you can install the rest of your system via any sort of network connection (including PPP after installation of the base system), via FTP, HTTP, or NFS.
The Debian boot disks contain a kernel which is built to maximize the number of systems it runs on. Unfortunately, this makes for a larger kernel, which includes many drivers that won't be used for your machine (see Compiling a New Kernel, Section 9.5 to learn how to build your own kernel). Support for the widest possible range of devices is desirable in general, to ensure that Debian can be installed on the widest array of hardware.
You must have at least 16MB of memory and 110MB of hard disk space. For a minimal console-based system (all standard packages), 250MB is required. If you want to install a reasonable amount of software, including the X Window System, and some development programs and libraries, you'll need at least 400MB. For a more or less complete installation, you'll need around 800MB. To install everything available in Debian, you'll probably need around 2 GB. Actually, installing everything doesn't even make sense, since some packages conflict with others.
The following network interface cards are supported directly by the boot disks on NetWinder and CATS machines:
The following network interface cards are supported directly by the boot disks on RiscPCs:
If your card is mentioned in the lists above, the complete installation can be carried out from the network with no need for CD-ROMs or floppy disks.
Any other network interface card (NIC) supported by the Linux kernel should also be supported by the boot disks. You may need to load your network driver as a module; this means that you will have to install the operating system kernel and modules using some other media.
Linux supports a large variety of hardware devices such as mice, printers, scanners, PCMCIA and USB devices. However, most of these devices are not required while installing the system. This section contains information about peripherals specifically not supported by the installation system, even though they may be supported by Linux.
There are several vendors, who ship systems with Debian or other distributions of GNU/Linux pre-installed. You might pay more for the privilege, but it does buy a level of peace of mind, since you can be sure that the hardware is well-supported by GNU/Linux.
Whether or not you are purchasing a system with Linux bundled, or even a used system, it is still important to check that your hardware is supported by the Linux kernel. Check if your hardware is listed in the references found above. Let your salesperson (if any) know that you're shopping for a Linux system. Support Linux-friendly hardware vendors.
Some hardware manufacturers simply won't tell us how to write drivers for their hardware. Others won't allow us access to the documentation without a non-disclosure agreement that would prevent us from releasing the Linux source code.
Since we haven't been granted access to the documentation on these devices, they simply won't work under Linux. You can help by asking the manufacturers of such hardware to release the documentation. If enough people ask, they will realize that the free software community is an important market.
Installing Debian GNU/Linux 3.0 For ARM
version 3.0.23, 16 May, 2002